Page updated May 15, 2019

|   Home  |   Amplification   |   Speakers   |
|  
Vacuum Tubes   |   Education   |   Support   |   Contact   |
 


 

The Wright Audio
Royale SE6 and SE610
 
Single-Ended Triode Stereo Integrated Amplifiers
 

Royale SE6 Integrated Amplifier

Royale SE6 Integrated Amplifier 


The Wright Audio Royale SE6 and SE610 Integrated Amplifiers are 'all-in-one', single-ended, triode-connected tube stereo amplifiers.  Due to the 'single-ended' circuitry, they have lower power output but are characterized by a more vivid, clear and harmonically-rich sound with greater dimensionality than solid-state, Class D or higher-powered 'push-pull' amplifier types whether using tubes or transistors.

These amplifiers provide greater clarity and more dynamics than other tube single-ended designs.  This is due to a careful selection of parts. a circuit topology and operating parameters all chosen for sound quality through extensive listening tests.  A custom-made, matched-channel Alps conductive plastic volume control, polypropylene and foil capacitors and output transformers created for wide bandwidth and high resolution have been employed.  The tubes are all biased into "Class A" service and the amplifiers require no maintenance or adjustment other than normal tube replacement.

Completely separate left and right channel power supply capacitors ensure added channel separation for lifelike stereo imaging.  There are no solid-state devices, integrated circuits, transistors or circuit boards anywhere in the amplifiers.

The music signal directly passes through just two capacitors and two very high gain vacuum tubes to preserve the integrity of the signal source.

These models were created  for use in smaller living areas such as apartments or similar situations, home or business, where listeners are required to be relatively close to the speakers and extreme volume levels are not required or tolerated.

The SE6 and SE610 Models are identical with the exception that the SE610 adds a stereo output for an active powered subwoofer system.

They accept six analog sources of any type except phono.  A separate phono preamplifier stage, such as the Wright Audio PH-2 Phono Stage is required for use with a phono cartridge.  The amplifier is compatible with all modern digital sources as long as an analog output is provided.

Professional music and video content producers will appreciate the SE610 as part of a computer audio monitoring system or work station to not only reveal recordings' shortcomings for corrections, but which will also impress clients with its outstanding sound quality during playback.

For all similar uses, the Wright Audio Royale SE6 and SE610 Integrated Amplifiers will suddenly involve you more intimately with the music you love.


Royale SE6 Integrated Amplifier 

 

FEATURES AND SPECIFICATIONS

  • *  Frequency Response: 25 to 30,000 cycles, within 1 db.  14 watts total output continuous.
     
  • *  SE6 Tube Complement:  (1) ECC83 / 12AX7, (1) GZ34 / 5AR4, (2) EL34, 6CA7 or KT77 tubes connected in triode mode. 
    SE610 Tube Complement:   (2) ECC83 / 12AX7, (1) GZ34 / 5AR3, (1) 12BH7 or 12AU7, (2) EL34, 6CA7 or KT77 tubes connected in triode mode. 
    No other tube numbers accommodated.

  • *  Controls: Power, Selector (CD, Tuner, Tape, Video, Spare 1, Spare 2), Left and Right Channel Level Presets (eliminates the 'half-set' Balance control), Volume,        Record 1, 2, 3 (Fixed-level passive outputs which may be used for recording, a stand-alone headphone amplifier or even a 'whole-house' wireless music distribution system with external transmitter.)
  • *  Accommodates all standard analog line-level sources or digital sources with an analog output.   For Phono use a separate phono preamplifier stage is required.
  • *  Vacuum tube, choke-filtered power supply provides the highest resolution, most pure sound, low noise and slow warm-up for longer parts life.
  • *  4 and 8 ohms speaker output standard.  8 and 16 ohms optional at extra charge.

    *  High quality RCA jacks and heavy duty, 30 amp - rated, 5 - way speaker binding posts accept banana plugs.

     
  • *  Externally - mounted fuse.
  • *  Detachable IEC power cable.
  • *  RoHS compliant parts used where applicable.
  • *  All point - to - point wiring.  Non-obsolescent construction.  No circuit boards for ease of installation of upgrades or repairs.
  • *  Glossy, black-anodized aluminum heavy-duty chassis (one-eighth inch thick top panel) for lowest electrical and mechanical noise.
  • *  Solid, red oak side panels. 
  • *  Size: 17 1/2" W  x  13 3/4" D  x  9" H
  • *  Net weight: 26 lbs;  Shipping weight: 32 lbs
  • *  Available in 120, 220 / 240 volt 50 / 60 cycle versions.  
  • THREE YEAR WARRANTY ((Tubes: 3 months)

  • *
     Designed and assembled in the U.S.A. with U.S. and global components.

Royale SE6 - SE610 Instruction Manual


Royale SE600 Back Panel
 


PRICE

$1495
Shipping:  $55 (Continental U.S.)

IN STOCK

Available only directly from Wright Audio.
Please allow an additional two days for the 220 / 240 volt version.

Select Voltage

 _______________________________________________________________

 

Royale SE610 Integrated Amplifier

Royale SE610 Integrated Amplifier

The Royale SE610 Integrated Amplifier is identical to the SE6 with the addition of a stereo output for an active subwoofer system.

 

Royale SE610 Integrated Amplifier 

Royale SE610 Integrated Amplifier Back

PRICE

$1635
Shipping:  $55 (Continental U.S.)

IN STOCK

 Available only directly from Wright Audio.
Please allow an additional two days for the 220 / 240 Volt version.

Select Voltage

 

|   Home  |   Amplification   |   Speakers   |
|  
Vacuum Tubes   |   Education   |   Support   |   Contact   |